Dascom 7206 Peeler Installation and User Guide Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Tiskárny Dascom 7206 Peeler Installation and User Guide. Dascom 7206 Peeler Installation and User Guide User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 14
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
– 1 –
Installation Guide 7106 7206
User Guide Peeler Unit
Zobrazit stránku 0
1 2 3 4 5 6 ... 13 14

Shrnutí obsahu

Strany 1 - User Guide Peeler Unit

– 1 –Installation Guide 7106 7206User Guide Peeler Unit

Strany 2

– 10 –3 How to operate3-1 Operation3 How to operate 3-1 Operation3-1-1 Peeler door opening/closing (1) Opening Shift the release knob of the peeler

Strany 3 - Installation Guide

– 11 –3 How to operate3-1 Operation3-1-4 Initial value of peeling position The paper position for peeling off the label can be adjusted in the printe

Strany 4 - Set 3 pcs screws

– 12 –3 How to operate3-1 Operation3-1-5 Peeler commands The following are the peeler commands. For details of each command, see the separate Command

Strany 5

– 13 –4 Peeler specifications 4 Peeler specifications Width of liner (a) : 1 − 4.65 in (25.4 − 118 mm) Length of label (b) : 1 − 4.72 in (25.4 − 1

Strany 6 - Connector cover

DASCOM REPRESENTATIVESGERMANYDASCOM Europe GmbHHeuweg 3D-89079 UlmDeutschlandTel.: +49 (0) 731 2075 0Fax: +49 (0) 731 2075 100www.dascom.comSINGAPORED

Strany 7 - User Guide

– 2 –© August 2010 DASCOM Europe GmbH

Strany 8 - Caution

– 3 –Installation Guide0 The following installation shows a 7106 printer. The peeler installation for 7206 printers follows the same steps.1 Before in

Strany 9

– 4 –1-3 Remove the screw (M3 X8, for plastic) and take the connector cover out as shown below.2 Installing the peeler2-1 While inserting the peeler c

Strany 10 - 3 How to operate

– 5 –2-2 Connecting the peeler unit cableConnect the peeler unit cable connector to the receptacle of the printer after setting the peeler cable in th

Strany 11

– 6 –3 Reinstalling the coversReinstall the connector cover (M3 X 8, for Plastic) and the motor cover (M3 X 6).Note: Keep the front cover for future u

Strany 12 - 3-1-5 Peeler commands

– 7 –User GuideContents Caution・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・81 Outline・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・92

Strany 13 - 4 Peeler specifications

– 8 –Caution Company names and product names in this manual are trademarks or registered trademarks of relevant companies. CAUTION Always use the p

Strany 14 - DASCOM REPRESENTATIVES

– 9 –1 Outline/2 Exterior view and part names 1 Outline This peeler unit is designed to automatically remove the label from the liner. 2 Exterior vie

Komentáře k této Příručce

Žádné komentáře